The treatment of waste-air containing mixed solvent using a biofilter 2. Treatment of waste-air containing ethanol and toluene in a biofilter

An experiment for five stages of a biofilter-run was performed to investigate the effect of hydrophilic ethanol and hydrophobic toluene on the biodegradation of hydrophobic toluene and hydrophilic ethanol, respectively, when waste-air containing toluene and ethanol was treated by a biofilter. Removal efficiencies of toluene and ethanol began to decrease when inlet load surpassed 90 g/m³/h and 100 g/m³/h consistent with maximum elimination capacities of toluene and ethanol, respectively. At the end of the biofilter-run, removal efficiencies for toluene and ethanol were decreased and maintained at 65% and 40%, respectively. The concentration of toluene at 1st sampling port was raised by factor of two in the 3rd stage of the biofilter run when the inlet load of ethanol co-feed was increased by 1.5 times, while the process conditions of toluene were maintained the same as those of the 2nd stage of biofilter-run. According to the result of Mohseni and Allen, it may be interpreted that removal efficiency of hydrophobic toluene was affected by the presence of hydrophilic ethanol when high load of hydrophobic toluene was applied like that of the 1st sampling port of the biofilter. However it was not the case when a low load of hydrophobic toluene was applied like those of the 2nd, 3rd and 4th sampling ports since hydrophobicity of toluene is much less that of α-pinene. Thus, it may be suggested that biodegradation of hydrophobic VOC was interfered by hydrophilic VOC dissolved in the biolayer and the degree of interference was proportional to the inlet load of hydrophobic VOC as well as that of hydrophilic VOC and was inversely proportional to the solubility of hydrophobic VOC. However, it was inferred that the existence of hydrophobic toluene from waste-air can hardly inversely hinder the removal of hydrophilic ethanol in the biofilter when timeevolutions of hydrophilic ethanol concentrations of this experiment were compared with those of the previous experiment of biofilter to treat waste-air containing ethanol only.     

Design and practical implementation of multifrequency RF front ends using direct RF sampling

The use of direct RF sampling has been explored as a means of designing multifrequency RF front ends. Such front ends will be useful to multifrequency RF applications such as global navigation satellite system receivers that use global positioning system (GPS) L1, L2, and L5 signals and Galileo signals. The design of a practical multifrequency direct RF sampling front end is dependent on having an analog-to-digital converter whose input bandwidth accommodates the highest carrier frequency and whose maximum sampling frequency is more than twice the cumulative bandwidth about the multiple carrier signals. The principle of direct RF sampling is used to alias all frequency bands of interest onto portions of the Nyquist bandwidth that do not overlap. This paper presents a new algorithm that finds the minimum sampling frequency that avoids overlap. This design approach requires a multifrequency bandpass filter for the frequency bands of interest. A prototype front end has been designed, built, and tested. It receives a GPS coarse/acquisition code at the L1 frequency and GPS antispoofing precision code at both L1 and L2. Dual-frequency signals with received carrier-to-noise ratios in excess of 52 dB-Hz have been acquired and tracked using this system.     

The relationship between photo-catalytic performance and optical property over Si-incorporated TiO2

This study focuses on the relationship between photo-catalytic performance and optical property over Si-incorporated TiO₂. The Si-incorporated TiO₂ particles exhibited a pure structure of anatase having a particle size of less than 20 nm and surface area of more than 190 m²/g. The absorbance did not shift to a higher wavelength in spite of the incorporation of the Si ions, but the intensity of the photoluminescence (PL) curve was the smallest in the case of the 2.0 mol% Si-TiO₂, which was related to the recombination between the excited electrons and holes. Based on these results, the photodecomposition of methyl orange in the liquid reaction was enhanced over the 2.0 mol% Si-incorporated TiO₂ compared with that over pure TiO₂: Methyl orange at 10.0 ppm was completely decomposed after 100 min when 1.0 g of the 2.0 mol% Si-incorporated TiO₂ was used.     

An investigation into physicochemical characteristics of ash produced from combustion of oil palm biomass wastein a boiler

Ash derived from combustion of Malaysian oil palm biomass (empty fruit bunches consisting of fibers) was physically and chemically characterized in order to provide a comprehensive understanding of its specific properties in terms of toxicity, compositions and reusability. Principal analyses conducted include particle size distribution, scanning electron microscopy, elemental dispersive X-ray, elemental analysis, toxicity characteristic leaching procedure (TCLP) as well as thermogravimetric, X-ray diffractometry and Fourier-transform infrared analyses. TCLP result indicated that the oil palm ash (OPA) should not be classified as toxic wastes in terms of heavy metal leachability since leachable copper, cadmium, lead and nickel concentrations were detected below the stipulated leachability limits. It was determined that the OPA contained high amount of potassium as well as presence of silica which implied its suitability to be reused as crude fertilizer or cement replacement material.     

Development of Stretch Solder Interconnections for Wafer Level Packaging

A wafer level packaging technique has been developed with an inherent advantage of good solder joint co-planarity suitable for wafer level testing. A suitable weak metallization scheme has also been established for the detachment process. During the fabrication process, the compliancy of the solder joint is enhanced through stretching to achieve a small shape factor. Thermal cycling reliability of these hourglass-shaped, stretch solder interconnections has been found to be considerably better than that of the conventional spherical-shaped solder bumps.     

In-situ microfracture observation of strip-cast Zr-Ti-Cu-Ni-Be bulk metallic glass alloys

In this study, Zr-Ti-Cu-Ni-Be bulk metallic glass (BMG) alloys containing a small amount of crystalline phase particles were fabricated by strip casting, and their improvement of mechanical properties and fracture toughness was explained by direct observation of the microfracture process. The compressive and fracture toughness test results indicated that strength, strain to failure, and fracture toughness of the strip-cast BMG alloy containing coarse crystalline particles were higher than those of the as-cast monolithic BMG alloy or the strip-cast BMG alloy containing fine crystalline particles. From in-situ microfracture observations, the improvement of overall mechanical properties of the strip-cast BMG alloy containing coarse crystalline particles could be interpreted by taking consideration of both the existence of coarse crystalline particles and the role of the particles to block crack propagation and to form multiple shear bands. Such property improvement suggests new applicability of the strip-cast BMG alloys containing coarse crystalline particles, which can work as toughening and strengthening reinforcements, to structures and components requiring excellent mechanical properties.     

Constitutive modelling and numerical simulation of multivariant phase transformation in superelastic shape‐memory alloys

This work concerns the micromechanical constitutive modelling, algorithmic implementation and numerical simulation of polycrystalline superelastic alloys under multiaxial loading. The model is formulated in finite deformations and incorporates the effect of texture. The numerical implementation is based on the constrained minimization of the Helmholtz free energy with dissipation. Simulations are conducted for thin tubes of Nitinol under tension–torsion, as well as for a simplified model of a biomedical stent. Copyright © 2004 John Wiley & Sons, Ltd.     

Highly ordered microstructures of poly(styrene-b-isoprene) block copolymers induced by solution meniscus

Microstructures of hundreds of micron thick poly(styrene-block-isoprene) copolymer films solution-cast in a cylindrical tube with the solvent evaporation controlled were investigated by transmission electron microscope (TEM), small angle X-ray scattering (SAXS) and optical microscope (OM). In a block copolymer with cylindrical polyisoprene microdomains, the orientation of the cylinders was varied along radial direction of the cylindrical tube. Highly aligned hexagonal arrays of in-plane polyisoprene cylinders were formed with their cylindrical axis parallel to the circumference of the tube in the regimes close to the wall edge. In contrast randomly ordered microdomains were observed at the center of the tube. We have also found that the orientation depends on the solvent evaporation rate and an intermediate rate (∼2.3 nL/s) provides the best orientation. In the case of a block copolymer with a bicontinuous double gyroid structure, we obtained a globally ordered microstructure where [111] crystallographic direction was parallel to the circumference of the tube. For both block copolymers, the area of highly ordered arrays of nanoscopic domains is over 1 mm². Development of the orientation was explained by coupling two orthogonal fields: (1) The flow of a solution induced by strong capillary force at a meniscus between the cylindrical tube wall and the block copolymer solution and (2) the solvent evaporation.     

Defining Yield from Bender Element Measurements in Triaxial Stress Probe Experiments

This paper describes the elastic response of a block sample of compressible Chicago glacial clay under a variety of stresses and its relationship with the deformation characteristics at relatively large strains. The elastic shear stiffness was obtained from bender element tests during consolidation and shearing in drained triaxial stress probe tests. An empirical correlation was established based on the elastic shear stiffness in a preyield condition. By comparing the empirical correlation with the measured elastic shear stiffness in the stress region during probing, the changes of elastic shear stiffness were investigated. The departure of elastic shear stiffness from values computed by the empirical relation based on K0 loading directly relates to the yielding characteristics of the clay. The large-scale change of soil structure at yielding alters the well-established relationship between the elastic shear stiffness and stresses in the preyield condition. The mechanical yielding response of clays can be detected based on the systematic analysis of the elastic shear wave velocities.